Product Specification
Product Configuration
| No. | Model | Name | Function |
|---|---|---|---|
| 1 | GT150B01 | Base module | Module for connection to each slot (with original I/F bus) |
| 2 | GT150U01 | Power & communication module | Power supply (external supply: 12V), PC-I/F(USB 2.1) |
| 3 | GT150SD1 | Storage module | Store measurement data in a stand-alone module |
| 4 | GT151M01 | RAM monitor module | Module for MCUs debug I/F |
| 5 | GT151C01 | CAN measurement module | Supporting high-speed CAN |
| 6 | GT151A0x | A/D measurement module | Module for analog measurement |
| 7 | GT102xxx | MCU probe | Refer to supported microcomputers |
* GT102 02: RAM module probe dedicated to RAMScope-EX
Specifications
| RAM Monitor module | MCU debug interface | NBD, AUD, AUDII, AUDR, RTD, NEXUS etc. |
|---|---|---|
| Measurement interval | 5us to 65s (Depends on the number of monitor channels and debug interface) | |
| Number of measurement channels | 1,024 points (max) | |
| Symbol watch (Memory R/W) | Variables: 64 points (max), (memory area: Read/Writing of 256 Byte (max)) | |
| Logging time stamp | Adds once every measuring period specified | |
| Monitor display | Real time display with Byte/Word/Long. Shows values in List Window and waveforms in Graphic Window. | |
| Event setting | Set No.: 8 points (event total with each module), Type: 8 patterns, Condition: OR/AND of each setting | |
| External trigger | Input: 1 point, Rating:-0.5 to +5.25V, External signal sampling measurement mode/External signal level measurement mode Output: 1 point, Rating: Select 3.3V or 5V, Scanning output/pulse output |
|
| File import/export | Import: A2L file format (ASAM MCD-2MC Data Specification Version 1.6), ELF/DWALF2 Export: MDF file format | |
| MCU probe | Connector for target side | 14 pin (2.54 mm pitch) Pin header: Connector (7614-6002xx) by 3M or equivalent |
| Environment | Temp range: -20 to +80C (The spec is different in each probe shape) Humidity range: 20 to 80%RH (No dewfall) | |
| CAN measurement module | CAN BUS | CAN Version 2.0B |
| Bit rate | 1M/ 800K/ 500K/ 250K/125K bps, High Speed CAN (ISO11898) | |
| Number of CAN channels/format ID | 2ch each module. Standard ID/Enhancing ID of each channel can be set | |
| Number of measurement messages | 1ch: 2,032 (max) | |
| Logging time stamp | Adds at each message received | |
| Monitoring display | Message: Byte unit display, Signal: Displays by length of the signal | |
| Event setting | Set No.: 8 points (event total with each module), Type: 8 patterns, Condition: OR/AND of each setting | |
| Connector type/Pin assignment | D-Sub 9pin x 2ch / CAN-H: 7, CAN-L: 2, GND: 3 | |
| Internal terminal circuit | 120 Ω SW-ON/OFF switching | |
| File import/export | ASC file format, CANdb format | |
| A/D measurement module | GT151A01 | Input range: ±60V (accuracy ±20 mV), Resolution: 2 mV, Impedance: Approx. 1 MΩ |
| GT151A02 | Input range: ±10V (accuracy ±5 mV), Resolution: 1 mV, Impedance: Approx. 1 MΩ | |
| GT151A03 | Input range: ±5V (accuracy ±3 mV), Resolution: 1 mV, Impedance: Approx. 1 MΩ | |
| Frequency characteristic, input filter | DC to 20 KHz, low-pass filter | |
| Number of input channels | 6ch, Non-isolation between channels | |
| Measurement interval | 10 us to 65s | |
| Logging time stamp | Stamps by sampling cycle | |
| Storage module | Object | Logging data from RAM monitor module/CAN measurement module |
| Record media | SDHC memory card (The memory cards other than the accessory are not guaranteed.) | |
| File format | RAMScopeV special format | |
| Memory card slot | 1ch with lock mechanism | |
| Logging time | Apprx. two hours in the accessory 8GB (Depends on the number of modules/ measurement channels, and the sampling duration) | |
| Time stamp | Measurement starting data in formation is added at the file translation. | |
| Switch PC or Storage | Mechanical switch in front | |
| Measurement [start/stop] | (1) Measurement start/stop switch: H/W switch (Alternate type) (2) Data logging stop by trigger (3) Measurement start and stop by presence of CAN data communication or specific ID generation |
|
| Common module | Base module | Connectable I/F: 5 |
| Power & Communication module | Rating: DC12V/2A max., Voltage range: 9.3 to16.0V | |
| Dummy module | Cover for unconnected interface of base module | |
| RAMScope-EX Spec | Measurement condition [start/stop] | Manual action, External trigger |
| Logging mode | [1-time][repeatable] according to trigger action condition | |
| Logging file format | CSV/Text/Binary Creates files for each module | |
| Environment | Temp range: 0 to 60C Humidity range: 20-80% RH (No dewfall) | |
| PC environment | Connectable I/F | USB 2.0 |
| Recommended host spec | CPU: Pentium4 3 GHz or more, Memory: 2 GB or more, Hard disk: Need 10GB or more OS: Microsoft Windows XP SP2, Windows 7 Professional/Ultimate *32-bit OS only |
System Example
