adviceLUNA II Support

FAQ

Search Keyword

Search Category

microVIEW-PLUS Debugger

  FAQ with this mark is a question which only the visitor by whom maintenance subscription was done can peruse.

Products / Install
• [Question] What is "License Server" button on the installer window?
• [Question] Is there any restrictions if restricted users use microVIEW-PLUS?
• [Question] Support of Windows7
• [Abnormal operation] Nothing is displayed on the selection window of ICE model.
• An error occurs when installing the install kit.
• Notes for versions of debugger
• What should I select for "Multicore debug" which is shown when creating a new project?
• This installation is forbidden by system policy. Contact your system administrator.
License
• [Error]MPU license error: Specified MPU license was not found.
• [Error]MPU license error: License is expired.
• [Error]MPU license error: License file not found
• [Error]MPU license error: License Error.
• [Error]MPU license error: MAC address is not correct.
Hardware / User-system's Interface
• If RTCK is stopped when MPU core clock supplying is stopped, can I continuously debug the program after restarting the clock supplying?
Error / Error Code
• [Error]S/W break is not supported for this flash memory.
• [Error]More than one CS area is specified.
• [Error]GetProcAddressError occurs when starting up the debugger.
• [Error] Cannot write "cmdlnk" in the cmdlnk command.
• [Error]The debugger which is executing cmdlnk command cannot be specified as a command link target.
• [Error]Cannot find the command link target.
• [Error]Failed to start up the external application.
• [Error] The process is canceled.
• [Question] I cannot start up the debugger. What should I do?
• [Error] Address is not specified correctly.
• Error No.992: Special area information file was not downloaded.
• ELF/DWARF2:Unable to obtain stack frame information.
• Error No.44: Cannot get the stack information
• GetProcAddress Error
• Error No.999: Monitor point function is not supported by converter output file.
• Error No.1
• Communication Error with ICE.
• Error No.46: Symbol is not found.
• Error No.732 Target is running.
• Error No.865: Cannot switch to MIX display mode.
• Error No.46: Cannot switch to ASM display mode.
• Unable to debug correctly, due to symbols have address conflicts.
• Error No.994: Cannot find the command link target.
• File Access Error For Symbol Search. Please copy JRE32.DLL in installation CD.
• Executing Command
• File Open Error
• Unable to Create Thread
• Function/Source File Not Found
• Invalid Mask Pattern
• Not Found
• No Available Resource
• Source Path Overflow
• Unavailable Type Found in Specified Symbol
• Unable to Register
• Invalid Name
• Invalid Address
• Register Name Already Registered
• Too Big Size
• Unable to Change Probe
• Variable out of Scope
• Error No.899: Version of the user registration register file is not correct.
• Target Is Running. Can't be changed.
• Invalid Group Name
• Unable to set up Group into a Group.
• Unable to Set for the Error generated immediately before.
• Invalid Group "END"
• There was no comparison data. Please check the address range or the file.
• There is no Source File to the address.
• Unable to enter same name symbol file.
• Unable to entry plural convert files.
• 512 or more path cannot be registered.
• The length of a path name is over 256 characters.
• Separate the path to convert and the path after conversion with a semicolon.
• The path to convert is invalid.
• The specified path after conversion does not exist.
• The conversion path rule is already registered.
• Not allowed to set up source path when using a file output by the converter.
• Invalid "start" of bit register definition was found.
• Invalid "start" of candidate string definition was found.
• Invalid "end" of candidate string definition was found.
• Invalid "end" of bit register definition was found.
• Bit pattern is described incorrectly.
• Bit size of the target user entry register exceeds the limit.
• Candidate character string is too long.
• Specify candidate character string.
• This bit pattern has been already registered.
• The number of definitions of candidate string exceeds the limit.
• The bit range was specified incorrectly.
• Character string of the name registered is too long.
• Character string of Outline is too long.
• The bit register name has been already registered.
• Invalid format
• Specified Path Not Found
• Specified environment variable not found.
• Register not found.
• No Register Group.
• The register group name not found.
• The Label Name is specified exceeding the limit.
• You need to set up address.
• You cannot edit a value with that register.
• Not allowed to register when Refresh at Break with log file output is checked on.
• Not allowed to register when Refresh Timer is checked on.
• Not allowed to delete when Refresh at Break with log file output is checked on.
• Not allowed to delete when Refresh Timer is checked on.
• The specified symbol name is not registered.
• Symbol name is not entered.
• Invalid offset value
• Debug Information File Access Error
• Unsupported Tool Chain. Unable to Access Symbol.
• Error No.5271: ELF/DWARF2:No Available STACK Frame Information
• Invalid Page Number
• Invalid Table Number.
• Illegal Load Number.
• Software Break Verify Error.
• Target Power OFF
• Setting Range Error
Operating with Memories, Registers
• How to specify address (numerical value)? How to specify the address range?
User-system Execution / Break
• Breakpoint list which you have set is not shown correctly.
• [Function/Specification] Break-rotational-display of the countable break
• [Abnormal operation] Cannot execute the step
Symbolic Debug
• [Error] Cannot open ELF debug information file
• [Error]Specified file name is not found.
• [Error] Over the maximum number of registrations of label.
• [Error] The label name has already used.
• [Error] Symbol library internal error
• [Function/Specification] Linux Support Library debug daemon
• [Error] Function/Source file is not found.
• What is the meaning of "/" shown next to the line number?
Commands
• [Error] Expression is not correct.
• [Question] Does command file support the argument?
• [Error] Not supported.
• [Function/Specification] How to change the address specification
• [Question] Can I use a nesting of macro file?
Application Example / Tips
• Can I specify the external file by relative path?
• Automatic registration of path conversion information
• Can I execute the command file by synchronizing with RESET?
Others
• Setting of "Update the display when a target break occurred" is not saved.
• Some lines become void when displaying a source code which contains Japanese and Korean in C mode.