adviceLUNA II Support
FAQ
Search Keyword
Please input a keyword.
Search Category
* adviceLUNAII / adviceLUNA(ICE)
microVIEW-PLUS Debugger
Please input a keyword.
* adviceLUNAII / adviceLUNA(ICE)
FAQ with this mark is a question which only the visitor by whom maintenance subscription was done can peruse.
- [Question] What is "License Server" button on the installer window?
- [Question] Is there any restrictions if restricted users use microVIEW-PLUS?
- [Question] Support of Windows7
- [Abnormal operation] Nothing is displayed on the selection window of ICE model.
- An error occurs when installing the install kit.
- Notes for versions of debugger
- What should I select for "Multicore debug" which is shown when creating a new project?
- This installation is forbidden by system policy. Contact your system administrator.
- [Error]MPU license error: Specified MPU license was not found.
- [Error]MPU license error: License is expired.
- [Error]MPU license error: License file not found
- [Error]MPU license error: License Error.
- [Error]MPU license error: MAC address is not correct.
- If RTCK is stopped when MPU core clock supplying is stopped, can I continuously debug the program after restarting the clock supplying?
- [Error]S/W break is not supported for this flash memory.
- [Error]More than one CS area is specified.
- [Error]GetProcAddressError occurs when starting up the debugger.
- [Error] Cannot write "cmdlnk" in the cmdlnk command.
- [Error]The debugger which is executing cmdlnk command cannot be specified as a command link target.
- [Error]Cannot find the command link target.
- [Error]Failed to start up the external application.
- [Error] The process is canceled.
- [Question] I cannot start up the debugger. What should I do?
- [Error] Address is not specified correctly.
- Error No.992: Special area information file was not downloaded.
- ELF/DWARF2:Unable to obtain stack frame information.
- Error No.44: Cannot get the stack information
- GetProcAddress Error
- Error No.999: Monitor point function is not supported by converter output file.
- Error No.1
- Communication Error with ICE.
- Error No.46: Symbol is not found.
- Error No.732 Target is running.
- Error No.865: Cannot switch to MIX display mode.
- Error No.46: Cannot switch to ASM display mode.
- Unable to debug correctly, due to symbols have address conflicts.
- Error No.994: Cannot find the command link target.
- File Access Error For Symbol Search. Please copy JRE32.DLL in installation CD.
- Executing Command
- File Open Error
- Unable to Create Thread
- Function/Source File Not Found
- Invalid Mask Pattern
- Not Found
- No Available Resource
- Source Path Overflow
- Unavailable Type Found in Specified Symbol
- Unable to Register
- Invalid Name
- Invalid Address
- Register Name Already Registered
- Too Big Size
- Unable to Change Probe
- Variable out of Scope
- Error No.899: Version of the user registration register file is not correct.
- Target Is Running. Can't be changed.
- Invalid Group Name
- Unable to set up Group into a Group.
- Unable to Set for the Error generated immediately before.
- Invalid Group "END"
- There was no comparison data. Please check the address range or the file.
- There is no Source File to the address.
- Unable to enter same name symbol file.
- Unable to entry plural convert files.
- 512 or more path cannot be registered.
- The length of a path name is over 256 characters.
- Separate the path to convert and the path after conversion with a semicolon.
- The path to convert is invalid.
- The specified path after conversion does not exist.
- The conversion path rule is already registered.
- Not allowed to set up source path when using a file output by the converter.
- Invalid "start" of bit register definition was found.
- Invalid "start" of candidate string definition was found.
- Invalid "end" of candidate string definition was found.
- Invalid "end" of bit register definition was found.
- Bit pattern is described incorrectly.
- Bit size of the target user entry register exceeds the limit.
- Candidate character string is too long.
- Specify candidate character string.
- This bit pattern has been already registered.
- The number of definitions of candidate string exceeds the limit.
- The bit range was specified incorrectly.
- Character string of the name registered is too long.
- Character string of Outline is too long.
- The bit register name has been already registered.
- Invalid format
- Specified Path Not Found
- Specified environment variable not found.
- Register not found.
- No Register Group.
- The register group name not found.
- The Label Name is specified exceeding the limit.
- You need to set up address.
- You cannot edit a value with that register.
- Not allowed to register when Refresh at Break with log file output is checked on.
- Not allowed to register when Refresh Timer is checked on.
- Not allowed to delete when Refresh at Break with log file output is checked on.
- Not allowed to delete when Refresh Timer is checked on.
- The specified symbol name is not registered.
- Symbol name is not entered.
- Invalid offset value
- Debug Information File Access Error
- Unsupported Tool Chain. Unable to Access Symbol.
- Error No.5271: ELF/DWARF2:No Available STACK Frame Information
- Invalid Page Number
- Invalid Table Number.
- Illegal Load Number.
- Software Break Verify Error.
- Target Power OFF
- Setting Range Error
- How to specify address (numerical value)? How to specify the address range?
- Breakpoint list which you have set is not shown correctly.
- [Function/Specification] Break-rotational-display of the countable break
- [Abnormal operation] Cannot execute the step
- [Error] Cannot open ELF debug information file
- [Error]Specified file name is not found.
- [Error] Over the maximum number of registrations of label.
- [Error] The label name has already used.
- [Error] Symbol library internal error
- [Function/Specification] Linux Support Library debug daemon
- [Error] Function/Source file is not found.
- What is the meaning of "/" shown next to the line number?
- [Error] Expression is not correct.
- [Question] Does command file support the argument?
- [Error] Not supported.
- [Function/Specification] How to change the address specification
- [Question] Can I use a nesting of macro file?
- Can I specify the external file by relative path?
- Automatic registration of path conversion information
- Can I execute the command file by synchronizing with RESET?
- Setting of "Update the display when a target break occurred" is not saved.
- Some lines become void when displaying a source code which contains Japanese and Korean in C mode.
Products / Install
License
Hardware / User-system's Interface
Error / Error Code
Operating with Memories, Registers
User-system Execution / Break
Symbolic Debug
Commands
Application Example / Tips
Others